View HP600_4297506.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Multi-Output HP600 AC-DC Front End Data Sheet
Features * Compact 1U design * N+1 redundancy with hot plug capability * Up to five individually-regulated outputs * 6.52 Watts/in3 power density * I2C interface with interrupt capability * Hot-swap with low insertion/extraction force connector * Power factor corrected * No minimum load required * 5 V @ 1 A standby output * Single-wire current sharing * Self-contained ORing diodes * Overcurrent and overvoltage protection * Full power up to 50 C * TUV, cTUVus & CB report * 600 watts per module * Two-year warranty
Description The HP600 provides up to 600 watts of output power with one to five main outputs ranging from 0.8 to 48 Volts, plus a 5V standby output. These hot-swap products incorporate internal ORing diodes and support paralleling and current sharing for up to three main outputs, excluding the -12V output. This multiple-output, hot-swap capability accelerates time-to-market in networking applications requiring several high-current rail voltages and/or instances where sufficient board space is not available to implement distributed power and intermediate bus architectures.
Model Selection
V1 HP6 Front End Models HP600-X8X4X4D2D-O HP600-X8X4X4D4D-O HP600-X4X4X4D4D-O HP600-X4X4X4D2D-O Volts X X X X Amps 80 80 40 40 Volts X X X X V2 Amps 40 40 40 40 V3* Volts Amps X 40 X 40 X 40 X 40 Volts 12 12 12 12 V4 Amps 20 40 40 20 Volts -12 -12 -12 -12 V5 Amps 3 3 3 3
Output Voltage X = A (2.0V); B (3.3V); C (5V); *F (24V @ 120W); *J (48V @ 120W); T (2.5V); V (1.8V); W (1.5V); X (1.2V); Y (1V); Z (0.8V) Options O = B (I2C); M (Output power good - TTL high); N (Power fail - TTL high); R (Reverse airflow) Please contact Power-One for additional model combinations.
May 16, 2007 revised to JUN 8, 2007
Page 1 of 6
www.power-one.com
Multi-Output HP600 AC-DC Front End Data Sheet
Input Specifications
Parameter AC Input Voltage Input Frequency Hold-up Time Inrush Surge Current Power Factor Conditions/Description Single-phase continuous input range. AC input. After last AC line peak at full power. At 115 VAC. Hot and cold start. At full load and nominal line. Min. 85 47 20 40 0.99 Nom. Max. 264 63 Units VAC Hz ms A pk W/VA
Output Specifications
Parameter Output Voltage and Current Ratings Efficiency Minimum Load Output Power Overshoot/Undershoot Output voltage overshoot/undershoot at turn-on or turn-off. 50% to 100% load step. Time required for initial output voltage stabilization after application of AC input or ON/OFF signal. Single-Wire Share (V1, V2, V3, and +12V) 10% full-load rating Compensates for voltage drop of up to 0.5V to the load (V1, V2, V3, and +12V). Shorted sense lead protection. Load with remote sense: Load without remote sense: Line over entire operating range: Cross: PARD: 1% or 50 mV pk-pk, whichever is greater; measured at 20 MHz bandwidth. 0.5 2 0.1 <5 % Conditions/Description See Model Selection table. Typical at full load, nominal input. No minimum load required. 78 0 600 <1 <3 <2 % A W % S Min. Nom. Max. Units
Start-Up Time
Current Share Remote Sense
Regulation
Output Noise and Ripple
May 16, 2007 revised to JUN 8, 2007
Page 2 of 6
www.power-one.com
Multi-Output HP600 AC-DC Front End Data Sheet
Interface Signals and Internal Protection1
Parameter LED Power Good Indicator LED AC Good Indicator Enable Output Good Signal Power Fail Signal Conditions/Description Front panel green LED indicates power supply is good; amber indicates a fault. Front panel green LED indicates AC input voltage is present and above minimum level. Normally TTL High; drive Low to enable. TTL compatible signal; normally Low (goes high when power supply is out of specified range). TTL compatible signal; normally Low (indicating AC input voltage is present and above minimum level). Internal 15A line fuse. All outputs set at 115 to 135% of nominal. Reset by cycling input power. All outputs set at 115 to 135% of full rated load with automatic recovery. Automatic shutdown with automatic recovery. Min. Nom. Max. Units
Input Protection Overvoltage Protection Overcurrent Protection Overtemperature Protection
Safety, Regulatory, and EMI Specifications
Parameter Agency Approvals Electromagnetic Interference Harmonics Voltage Fluctuation and Flicker ESD Susceptibility Radiated Susceptibility EFT/Burst Input Transient Protection RF Conducted Immunity Leakage Current Dielectric Withstand Conditions/Description TUV, cTUVus, & CB Report Meets EN55022, Class B. Meets IEC61000-3-2. Per IEC61000-3-3, Criteria B. Per EN61000-4-2, Criteria B. Per EN 61000-4-3, Criteria A. Per EN 61000-4-4, Criteria B. Per EN 61000-4-5, Criteria B. Per EN 61000-4-6, Criteria A. At 240 VAC, 50 Hz Input-to-Ground: Input-to-Output: Output-to-Case: . . . . . 1.2 2200 4300 25 mA VDC Min. Nom. Max. Units
May 16, 2007 revised to JUN 8, 2007
Page 3 of 6
www.power-one.com
Multi-Output HP600 AC-DC Front End Data Sheet
Environmental Specifications
Parameter Altitude Operating Temperature Storage Temperature Temperature Coefficient Relative Humidity 0 C to 50 C Non-condensing. Conditions/Description Operating. Non-Operating. Internal DC fan for cooling. 0 -40 Min. Nom. Max. 10K 40K 50 85 0.02 95 Units ASL ft ASL ft C C %/C %RH
Reliability
Parameter MTBF Conditions/Description (Calculated) @ 25 C, Bellcore Standard. Min. 250 000 Nom. Max. Units hrs
I2C Interface The HP600 I2C interface provides highly-integrated error monitoring and analyses, and includes the following features:
Event-Driven Messages:
* * * * * * * * * * * *
Notification of fan-speed abnormality Output voltage under specified 'good' range Output voltage over specified 'good' range (software OVP) Temperature abnormalities Get voltage readings Get temperature readings Get fan-speed readings Manufacturer's name Product name Product part/model number Product version/revision Product serial number
Sensor Device Commands:
FRU (Field Replaceable Unit) Information Storage:
May 16, 2007 revised to JUN 8, 2007
Page 4 of 6
www.power-one.com
Multi-Output HP600 AC-DC Front End Data Sheet
Mechanical Specifications Size: 1.6" H x 5" W x 11.5" D (40.6 x 127 x 292.1 mm) Connector: FCI 51939-046 I/O Mating Connector: FCI 51921-001
May 16, 2007 revised to JUN 8, 2007
Page 5 of 6
www.power-one.com
Multi-Output HP600 AC-DC Front End Data Sheet
Output Connector Details
J1 DC Output and Signal Interface Pinout
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Signal Name V4 Output (+12V) V4 Output (+12V) Ground Ground V1 Output V1 Output V1 Output Ground Ground V2 Output V2 Output Ground Ground V3 Output V3 Output Chassis AC Low AC High Pin No. A1 A2 A3 A4 A5 B1 B2 B3 B4 B5 C1 C2 C3 C4 C5 D1 D2 D3 D4 Signal Name +Sense V1 Share V3 Share V1 Share V4 DC Enable Present +Sense V3 Share V2 +Sense V2 SCL V5 Output (-12V) 5V Standby +Sense V4 - Sense A1 V5 Output (-12V) 5V Standby Power Fail * Power Good **
D5
NOTES: * AO with I C option ** Interrupt with I C option
2 2
SDA
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice.
May 16, 2007 revised to JUN 8, 2007
Page 6 of 6
www.power-one.com

▲Up To Search▲

Price & Availability of HP600

	To Download HP600 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .